/wwg/ Woodworking General ... I am moving up north soon where everything is 3x as expensive. My new house has a large garage though, and I'd like to have a workshop. I just don't know what I should bu...
Thread: https://boards.4channel.org/diy/thread/2782716
Contractor/flooring fags ... If I have a sleeper subfloor (2x4&OSB) over a concrete basement slab, is a moisture barrier still absolutely required? Im getting mixed results everywhere i look -The 2x4...
Thread: https://boards.4channel.org/diy/thread/2783087
What should a computer desk have? I'll make one from scratch.
Thread: https://boards.4channel.org/diy/thread/2782793
What's this white stuff coming out of this wooden door's crack?
Thread: https://boards.4channel.org/diy/thread/2782737
Another Battery Operated Tools Question ... So there is always talk about the big brands, best color, and even cord vs cordless but I have a serious question: Which Chinese brand(s) mix and match with...
Thread: https://boards.4channel.org/diy/thread/2782862
Reducing Ceiling Fan Speed ... I have a 6-speed brushless DC ceiling fan. All 6 speeds are too fast for winter use. Bought/installed a different receiver/remote set and it runs a little slower on lowe...
Thread: https://boards.4channel.org/diy/thread/2782757
Coin Cleaning ... Not sure if this is the right board for this, but I can't think of a better one. I was going through some old boxes that were in storage recently when I happened across my childhood...
Thread: https://boards.4channel.org/diy/thread/2782674
*ROAD SPIKES* ... Does anyone know how to build them? (i have tried a few times and it turned out pretty well by just hammering a nail into a piece of wood, but i don't know how effective it is gonna ...
Thread: https://boards.4channel.org/diy/thread/2782512
What is this stuff coming off over my radiator? Is it plaster or paint? Can there be asbestos?
Thread: https://boards.4channel.org/diy/thread/2782483
Would a small 1hp lathe be able to drill a 12mm and 20cm of depth in 4140 steel? assuming the proper drill bit and speed is used? If not what's the minimum hp needed?
Thread: https://boards.4channel.org/diy/thread/2782390
Dropped a basically empty (flashed if you tried to run a tool with it) M18 battery in water the other day, pulled it out and it was soaked, you could see drops of water inside the battery check button...
Thread: https://boards.4channel.org/diy/thread/2781944
Anyone have tips for how to fell a tree with a straight cut rather than taking a notch out of it? I want to use this cedar for an artsy project and I'd like to maximize the amount of lower trunk I get...
Thread: https://boards.4channel.org/diy/thread/2781643
Formulating a glue for ultra-thin applications? ... For a project I'm working on, I need to manually laminate an extremely thin, stretched Mylar membrane (around 1μm) with a gold leaf. I've had succ...
Thread: https://boards.4channel.org/diy/thread/2781657
So, i want to be a machinist. Bad. I have a lot of mechanical experience from working in industrial maintenance. I got a referral from a guy, and the upper structure of this company is sending me long...
Thread: https://boards.4channel.org/diy/thread/2781913
How the fuck do you clean car windows and not leave streaks or marks? Ive tried windex, sprayway, invisible glass, rainx ceramix Ive had this car for 4 years and 50k miles now, and the only time the w...
Thread: https://boards.4channel.org/diy/thread/2781677
So is Ryobi really that bad or is it just a meme?
Thread: https://boards.4channel.org/diy/thread/2781888
I want to start making my own granola bars because Iâm tired of getting jewed and paying $7 for a box. I bought all the ingredients I want in them but what do you use to get everything to clump toge...
Thread: https://boards.4channel.org/diy/thread/2781838
Commercial Dishwashing Chemicals ... What are the best chemicals for breaking down shit that's stuck to dirty kitchen equipment? Dishwashing liquid is inferior. There must be better shit out there. I ...
Thread: https://boards.4channel.org/diy/thread/2781715
Why have popcorn ceilings become so unpopular?
Thread: https://boards.4channel.org/diy/thread/2781580
